Basic Specifications

Display Block		10.4-inch TFT color LCD Effective screen area: 211.2 mm x 158.4 mm (640 dots x 480 dots)
Printer Block (RA1200/RA1300)
	Printing method	Thermal printing using a thermal head
	Paper Width	219.5 mm
	Effective Recording Width	1 split (200mmFS) to 16 splits (10mmFS), Numberofsplit and printing width can be changed.
	Channel Discrimination	Prints channel number in the vicinity of theprintedwaveform The ON/OFF function is available.
Battery Backup		Backup Contents: Main unitsettings,Recording conditions Backup time: About 1 month (if fully charged and used undernormaltemperature)
Storage Devices		A built-in 3.5-inch floppy diskdrive(1.25MB/1.44MB) PC card slot (ATA flash memory card, SRAM card) Built-in MO unit (640, 540, 230, and 128MB supported): optional
Interface		RS-232C unit (38400 to 2400 bps): optional GP-IB unit (IEEE488 compliant): optional SCSI unit (50-pin type): optional
Remote Terminal		Start/stop, mark print, and paper feed areavailableby external signal, synchronous pulse Input, protect input, output ofwaveformjudgement results, and error output
Clock Function		Stability: Daily error within ±35 PPM (atnormaltemperature)
Operating Environment		Temperature: 0 to 40°C (5 to 40°CwhenFFD is operating) Humidity: 35 to 80% RH (without condensation) Vibration Resistance: MIL-STD-810E compliant (except when FDorMOis operating)
Power Supply		90 to 132 VAC/180 to 264 VAC (to be specifiedwhenordering) Frequency 47 to 63Hz DC power unit (optional) In use: 11 to 28 VDC(AC powerisprioritized)
PowerConsumption(Maximum)		RA1100: Approx. 85 VA RA1200: Approx. 180 VA (About 85 VA during stand-by) RA1300: Approx. 350 VA (About 85 VA during stand-by)
Dimensions		Approx. 369.5 (W) x 150.5 (H) x 301(D)mm
Weight		Approx. 6.6kg (RA1100 main unit withfour2-ch high-resolution DC amps) Approx. 7.5kg (RA1200 main unit with four 2-ch high-resolutionDCamps) Approx. 7.5 kg (RA1300 main unit with four 2-ch high-resolutionDCamps)

Trigger Specifications

Trigger Mode	OR, AND, A*B, WINDOW
Trigger Source	Input Signal, time trigger(startingtime, ending time, measurement interval), manual trigger and external trigger
Trigger Setting	Amps other than event amps   Trigger Slope OR, AND.....or     A*B...orfor each A,B source     WINDOW...OUT or IN Level Setting: To besetwith physical values (e.g. voltage)
	Event Amp   State Settings: H, L, or OFF can be set for each input(withouttrigger slope) When OFF is set, trigger condition is notapplied.   Trigger Setting: AND or OR of the statesettingconditions of inputs from 1 to 8
Trigger Related Functions	Pre-trigger , trigger pass count,triggerfilter, and trigger mark

Other Specifications

PrintFunctions(RA1200/RA1300)
	Data Information	Measurement mode,year/month/day,Measurement start time, Data No., Trigger conditions (Trigger point, Trigger year/month/day,Triggertime), Sampling speed, Chart speed, Time axis, etc. areprintedsimultaneously with waveform print). ON/OFF function is available.
	Channel Information	Input unit settings areprintedsimultaneously. ON/OFF function is available.
	Mark print	In the real-time mode, the mark printisavailable (M date/time)
	List Print.	Date, time, measurement mode, data No.,record form, chart speed, sampling speed, scale printing, back-light auto-off, autostart,buzzer click, trigger mode, source channel, recording operation,filingsetting printout
	Screen Copy Function	Prints hard copies of the contentsshownon the screen
	A4 report output	Registers free comments and printsthemtogether with the waveform printing
	Printing Line Width	Sets baseline boldness (1, 2, 3, 4dots)for each channel
Key Lock Function		Invalidates key input topreventerroneous operation
Storing and ReadingofSettings		Up to four conditions for input unitandmain unit settings are stored in the main unit memory
PhysicalValueConversion		Physical conversion of inputsignal,full-scale modification of display
Stand-by Function		When the main unit is restoredfromblackout or temporary halt, original state is regained.(Except when filing)
AutomaticSetupFunction		By presetting a floppy diskcontainingthe measurement conditions in FD drive, the conditions are automatically read when turning onthepower.
Storing theScreenImage		Stores a screen image in bitmapformatinto a floppy disk
Help Function		Displays the handling method,cautions,etc.
RS-232C Unit Function
	Remote Control	Controls the main unit from a personal computerviathe RS-232C cable.
	FAX Transmission Function	Sends measured waveform by using a FAXmodemconnected to RS-232C.
GB-IB Unit Function
	Remote Control	Controls the main unit from a personal computerviaGB-IB cable.
SCSI Unit Function
		Stores data to MO or PD as externalmemorydevices.

AC Bridge Power Supply Unit (Optional)

Function	Bridge power source for 2-ch ACstrainamp
Power Voltage, Carrier Wave	2 Vms, Sine wave 5kHz
Synchronism	Synchronization with other RA1000susinga built-in AC bridge power unit is available.

Memory Mode

Measurement Operation		Once, Repeat, Endless
Memory Capacity		256kW/CH (Max.1 MW/CHoptionallypossible) *When function operation is used, memory capacity is 1/4 When two channels are used, 2MW/CH is the maximum
Memory Division		1, 2, 4, 8, 16, 32, 64, and128divisions
Sampling		1 µs (1 MS/s) to 1 s(1S/s),User-settableExternal synchronization enabled
Display(ReplayMonitor)
	Waveform Display	Display magnification :x5 to x1/1000
	X-Y Display	X-Y display where data of an anychannelis shown on the X axis, and other channel on the Y axis. Display step: 1 to 1000 steps
Print (RA1200/RA1300)
	Waveform Print	Print Density: Voltage axis: 8dots/mmTime axis: 10 dots/mm Copy magnification: x5 to x1/1000
	Alphanumeric Print	Readout Interval : 1 to 1000 steps
	X-Y Print	X–Y print where data of an any channelisshown on the X axis, and other channel on the Y axis. Effective print range : 200 mm x 200mmPrint density : 400 dots (X axis) x 400 dots (Y axis) Display step : 1to1000 steps
Memory Filing		Each time data is stored into memory,thedata is saved in the memory device in the binary or CSV format.

Real-Time Mode (RA1200/RA1300)

Waveform Printing
	Measurement Starting Operation	Starts with the Start key, by thetriggerdetection, or at set time. Interval recording available.
	Paper Speed	25 mm/s to 1 mm/sec (RA1200), 100 mm/sto1 mm/min (RA1300), User settable. External synchronization enabled
	Frequency Response	DC to 100 kHz (sampling points:10points/cycle), Varies depending on the input units
	Printing Density	Voltage axis : 8 dots/mm Time axis :RA1200 :10 dots/mm   :RA1300 :20 dots/mm at 100 mm/s     :40 dots/mm at 50 mm/s     :80 dots/mm at 25 mm/s
	Printing Length	Continuous or 1 to 1000division-shotfeeding
Alphanumeric Printing
	Sampling	1 s to 1 hour, User settable,Externalsynchronization enabled
	Printing Length Setting	Continuous or 1 to 1000 data shot feeding
X-Y Printing
	Performance	X-Y recording where data of ananychannel is shown on the X axis, and other channel on the Y axis. Continuous recording until stopbuttonis pressed (pose function available)
	Effective Printing Range	200 mm x 200 mm
	Printing Density	400 dots (X axis) x 400 dots (Y axis)
	Printing Speed	10 ms or more
Backup Filing		Stores the measured data in amemorydevice in real-time Recording Speed: Synchronized with paper speed

Transient Mode

TransientRecording(RA1200/RA1300)
	Function	Normally operates in the real-timemode.When trigger is detected, the mode is switched to the memory mode.
	Real-time Section	In conformance with the waveformprintingin the real-time mode
	Memory Section	In conformance with data storageandprinting in the memory mode
Transient Filing
	Function	Normally operates in backup filing,datais saved in a memory when trigger is detected, and whenmeasurementfinishes, the memory data is saved.
	Real-Time Section	In conformance with backup filing in thereal-timemode
	Memory Section	In conformance with memory filing inthememory mode

Filing Mode

Data Recording
	Function	Stores the measured data real-time toamemory device (Real time filing)
	Recording Speed	200 µs to 60 s. Maximum recordingspeedvaries depending on number of channels and recording device. User settableExternalsynchronization ennobled
	Recording Method	Select normal or ring Ring recording is possible (Repeated recording during set time)
WaveformPrinting(RA1200/RA1300)
	Function	Prints the waveform of input signal
	Paper Speed	25 mm/s to 1 mm/m (RA1200), 100 mm/s to1mm/m(RA1300) User Settable External synchronization enabled
	Frequency Response	DC to 100 kHz (sampling point:10points/cycle), Varies depending on the input units
	Printing Density	Voltage axis : 8 dots/mm Time axis :RA1200 :10 dots/mm   :RA1300 :20 dots/mm at 100 mm/s     :40 dots/mm at 50 mm/s     :80 dots/mm at 25 mm/s

FFT Unit (Optional)

1 Signal Analysis		Linear spectrum, power spectrum, RMS spectrum,powerspectrum density, and octave analysis (1/1, 1/3)
2 Signals Analysis		Transfer function, coherencefunction,and cross-power spectrum
Window Function		Rectangular, hanning,hamming,exponential, force
Addition Processing		Simple additional average (timeaxis),simple additional average (frequency axis), exponential weighted average (frequencyaxis),and peak hold
Analysis Frequency		400kHz, 200kHz, 80kHz, 40kHz,20kHz,10kHz, 5kHz, 2kHz, 1kHz, 500Hz, 200Hz, 100Hz, 50Hz, 20Hz, and 10Hz
Resolution		400 (1000), 800 (2000), 1600 (4000) Numbers in parentheses indicates the number ofsamplingpoints.

Arithmetic Operation Unit (Optional)

SectionalStatisticalOperation		Maximum value, minimum value, P-P value,averagevalue, area, effective value, standard deviation, risingtime,falling time
Function Operation		Four-function calculation,absolutevalue, differential, integration, secondary differential,doubleintegration, square root, exponential, common logarithm,movingaverage, and trigonometric functions (sin, cos,tan, asin,acos,atan)

Waveform Judgment Unit (Optional)

Function		Measures waveform of input signals ofeightchannels, and outputs the results of waveform judgement
Targets ofOutputtingResults		Print on paper, FAX, data storage,orremote terminal output

2-CH High Resolution Amp (AP11-101)

Input		2channels/unit, isolated unbalanced input,isolatedBNC connector
Input coupling		AC and DC coupling
Input impedance		1Mor higher
Measurement range		0.1, 0.2, 0.5, 1, 2, 5, 10, 20, 50,100,200, and 500 V
Range accuracy		Within 0.3% FS (Within 0.8% FS at 500V)
Offset accuracy		Within 0.3% FS (at 25°C)
Linearity		Within 0.1% FS
Allowableinputvoltage		Range of 10 V to 500 V: 500 V max.(ACor DC peak values) Range of 0.1 V to 5 V: 100 V max. (AC or DC peak values)
CMV		Unit only: 43 V (AC or DCpeakvalues)When using isolated BNC cable (optional): 300 VAC
Frequency response		At DC coupling: DC to 50 kHz (+0.5,-3dB) At AC coupling: 0.3 to 50 kHz (+0.5, -3 dB)
Low-pass filter		Bessel type (attenuation factor:-12dB/OCT) 30, 300, 3 kHz, and OFF (+0.5, -3 dB)
A/D converter		16 bits, 100 kHz max. (twochannelsimultaneous sampling)
Temperature stability		Zero point: Within 0.03% FS/°C Gain (range): Within 0.01% FS/°C
Weight		230 g

2-CH High Speed Amp (AP11-103)

Input		2channels/unit, isolated unbalanced input,isolatedBNC connector
Input coupling		AC and DC coupling
Input impedance		1Mor higher
Measurement range		0.1, 0.2, 0.5, 1, 2, 5, 10, 20, 50,100,200, and 500 V
Range accuracy		Within 0.5% FS (Within 0.8% FS at 500V)
Offset accuracy		Within 0.5% FS (at 25°C)
Linearity		Within 0.2% FS
Allowableinputvoltage		Range of 10 V to 500 V: 500 V max.(ACor DC peak values) Range of 0.1 V to 5 V: 100 V max. (AC or DC peak values)
CMV		Unit only: 43 V (AC or DCpeakvalues)When using isolated BNC cable (optional): 300 VAC
Frequency response		At DC coupling: DC to 400 kHz (+0.5,-3dB) At AC coupling: 0.3 to 400 kHz (+0.5, -3 dB)
Low-pass filter		Bessel type (attenuation factor:-12dB/OCT) 50, 500, 5 kHz, and OFF (+0.5, -3 dB)
A/D converter		12 bits, 1 MHz max. (twochannelsimultaneous sampling)
Temperature stability		Zero point: Within 0.03% FS/°C Gain (range): Within 0.01% FS/°C
Weight		240 g

2-CH TC/DC Amp (AP11-106)

Input		2channels/unit, isolated unbalanced input,terminalblock 4
Input coupling		DC coupling
Input impedance		10Mor higher
Thermocouple		R, T, J, K, and W
Measurement range		R: 0 to 1600°C T: -200 to 400°C J: -200 to 1000°C K: -200 to 1350°C W: 0 to 2300°C
Voltagemeasurementrange		100, 200, 500 mV, 1, 2, 5, 10, 20 and50V FS
Range accuracy		Temperature: Within 0.5% FS (Within1%FS at 0°C or lower) Voltage: Within 0.5% FS
Coldjunctioncompensation		Internal/external switchable Accuracy: Within 2°C (Within 1°C at stable temperature of 20°Catinput terminal)
Linearity		Within 0.1% FS
Allowableinputvoltage		50 V (AC or DC peak values)
CMV		43 V (AC or DC peak values)
Frequency response		DC to 40 kHz (+0.5, -3 dB)
Low-pass filter		Bessel type (attenuation factor:-18dB/OCT) 1, 30, 500, 5 kHz, and OFF (+0.5, -3 dB)
A/D converter		15 bits, 100 kHz max. (twochannelsimultaneous sampling)
Temperature stability		Accuracy: 0.04% FS/°C (When usedastemperature amp) Zero point: Within 0.03% FS/°C (When used as DC amp) Gain (range): Within 0.01% FS/°C
Weight		240 g

TC/DC Amp (AP11-107)

Input		1 channel/unit, isolated unbalanced input, 2bindingposts
Input coupling		DC coupling
Input impedance		10M or higher (1M at 5, 10, 20, 50 V FS in DC amp)
Thermocouple		R, T, J, K
Measurement range		R: 0 to 800°C at 800°C FS and 0to1600°C at 1600°C FS T: -200 to 200°C at 200°C FS and -200 to 400°C at 400°CFS J: -200 to 200°C at 200°C FS and -200 to 1000°C at 1000°C K: -200 to 200°C at 200°C FS and -200 to 1200°C at 1200°C
Voltagemeasurementrange		10, 20, 50, 100, 200, 500 mV, 1, 2,5,10, 20, and 50 V FS
Range accuracy		Temperature: Within 0.5% FS (Within1%FS at 0°C or lower) Voltage: Within 0.5% FS
Linearity		Within 0.1% FS
Allowableinputvoltage		50 V (AC or DC peak values)
CMV		300V (AC or DC peak values)
Frequency response		DC to 40 kHz (+0.5, -3 dB)
Low-pass filter		Bessel type (attenuation factor:-18dB/OCT) 1, 30, 500, 5 kHz, and OFF (+0.5, -3 dB)
Referencejunctioncompensation		Internal/external switchable
A/D converter		14 bits, 100 kHz max.
Weight		200 g

Event Amp (AP11-105)

Number of channels		8 channels/unit
Input signal		Sets voltage or contact foreachchannel Voltage input: Input voltage range 0 to +24 V Detection level H level...2.5 V or higher   L level...0.5 V or lower Contact input: Close...250 or lower   Open...2 kor higher
Response time		1µs or faster (Input level should be+5V or higher.)
Input connector		Round DIN connector 8P...2 pcs. Event amp side: XT2B-0800(Conformed to DIN45326)
Weight		100 g

2-CH AC Strain Amp (AP11-104)

Number of channels		2 channels/unit, isolated balanced input,NDISconnector
Applicablegaugeresistance		120to 1k
Bridge power supply		Sine wave 2 Vrms, 5 kHz (Bridgepowersupply is supplied separately.)
Gauge factor		1.9 to 2.2
Range of balance		Resistance: 2% (10000 µ)or lower Capacitance: 2000 pF or lower
Balance method		Resistance: Auto-balance Capacitance: Auto-balance (500 pF or lower,eliminatingconstantly) Balance time: Within 1s at 1 ch Within 0.5%Fs Remainedvoltageaccuracy
Maximum sensitivity		Over full-scale at 500 µ(at 2 V or higher bridge voltage)
Measurement range		1, 2, 5, 10, 20 kµFS
Internalcalibratorand accuracy		0.5 k, 1 k, 2 k, 3 k, 5 kµAccuracy: Within 0.5% FS
Linearity		0.2% FS
CMV		300 VAC
Frequency response		DC to 2 kHz (+0.5, -3dB)
Low-pass filter		Butterworth type (attenuationfactor:-12 dB/OCT) 10, 30 , 100, 300 Hz, and OFF (+0.5, -3 dB)
A/D converter		16 bits, 100 kHz max.
Temperature stability		Zero point: Within 0.05% FS/°C Gain (range): Within 0.05% FS/°C
Weight		285 g

2-CH DC Strain Amp (AP11-110)

Number of channels		2 channels/unit, isolatedbalancedinput, NDIS connector
Input coupling		DC
Input impedance		10M+10Mor higher
Bridge power supply		2 V and 5 V
Applicablegaugeresistance		120 to 2 k (at BV = 2V),350 to 2k (at BV=5 V)
Gauge factor		2
Range of balance		2% (15000 µorlower
Balance method		Resistance: Auto-balance Balance time: 0.5 sec max. at 1ch Remained voltage accuracy: Within 0.3% FS
Measurement range		2, 5, 10, 20, 50 kµFS (at BV = 2 V) 0.8, 2, 4, 8, 20 kµFS(BV= 5 V)
Voltagemeasurementrange		2, 5, 10, 20, 50 mV FS
Range accuracy		Within 0.3% FS
Linearity		0.1% FS
Allowableinputvoltage		8 V (DC or AC peak values)
Frequency response		DC to 50 kHz (+0.5, -3dB)
Low-pass filter		Bessel type (attenuation factor:-12dB/OCT) 10, 30, 300 Hz, 1 kHz, and OFF (+0.5, -3 dB)
Temperature stability		Zero point: Within 0.1% FS/°C Gain (range): Within 0.01% FS/°C
CMV		300 VAC
A/D converter		16 bits, 100 kHz max
Weight		240 g

2-CH Vibration/RMS Amp (AP11-109)

Input		2 channels/unit, isolatedunbalancedinput, isolated BNC connector
Input coupling		AC and DC
Input impedance		10 Morhigher
Power supplyforsensor		2 mA, 18 V or higher
Measurement range		0.1, 0.2, 0.5, 1, 2, 5, 10, 20, 50,100,200, 500 V
Range accuracy		DC amp range: Within 0.3% FS(Within0.8% FS at 500 V) RMS amp range: Within 2% FS (at DC and 40 Hz to 20 kHz)
Linearity		Within 0.1% FS
Crest factor		2.8 max. (RMS amp)
CMV		Unit only: 42 V (DC or ACpeakvalues) When isolated BNC cable (optional) is used: 300 V AC
Frequency response		DC coupling: DC to 50 kHz (+1,-3dB) AC coupling: 1 to 50 kHz (+1, -3 dB)
Low-pass filter		Butterworth type (attenuationfactor:-24 dB/OCT) 30, 100, 300 Hz, 1 kHz, and OFF
High-pass filter		Butterworth type (attenuationfactor:-24 dB/OCT) 10, 30, 100 Hz, and OFF
A/D converter		16 bits, 100 kHz max.
Temperature stability		Zero point: Within 0.02% FS/°C Gain (range): Within 0.01% FS/°C
Weight		270 g

2-CH FFT Amp (AP11-102)

Input		2 channels/unit, isolatedunbalancedinput, isolated BNC connector
Input coupling		AC and DC (only AC couplingwhenamp-embedded charge accelerometer is used)
Input impedance		1 Mor higher
Power supplyforsensor		2 mA, 18 V or higher
Measurement range		0.1, 0.2, 0.5, 1, 2, 5, 10, 20, 50,100,200, 500 V
Range accuracy		Within 0.3% FS (Within 0.8% FS at 500V)
Linearity		Within 0.1% FS
Maximum input voltage		500 V (DC or AC peak values) (30 V atACcoupling of 0.1 to 5 V)
CMV		Unit only: 42 V (DC or ACpeakvalues) When isolated BNC cable (optional) is used: 300 V AC
Frequency response		DC coupling: DC to 50 kHz (+0.5,-3dB) AC coupling: 0.3 to 50 kHz (+0.5, -3 dB)
Low-pass filter		Bessel type (attenuation factor:-24dB/OCT) 30, 300 Hz, 3 kHz, and OFF (+0.5, -3 dB)
Anti-aliasing filter		20, 40, 80, 200, 400, 800 Hz, 2, 4,8,20, and 40 kHz Drop characteristic: -72 dB typ. at 1.5 x fc
Offset accuracy		Within 0.3% FS (at 25 °C)
A/D converter		16 bits, 100 kHz max.
Temperature stability		Zero point: Within 0.02% FS/°C Gain (range): Within 0.01% FS/°C
Weight		240 g

F/V Converter (AP11-108)

Input		1 channel/unit, isolatedunbalancedinput, isolated BNC connector
Input coupling		AC and DC
Input impedance		100 M or higher
Input frequency range		1 Hz to 10 kHz (Pulse width: 20 µsorlonger)
Measurement range		0.1, 0.2, 0.5, 1, 2, 5, 10 kHz FS
Range accuracy		Within 0.5% FS (Within 0.8% FS at 500V)
Linearity		Within 0.3% FS
Trigger level		Selectable from 0 V and 2.5 V
Allowableinputvoltage		100 V (AC or DC peak values)
CMV		Unit only: 42 V (AC or DCpeakvalues) Between isolated BNC and safety terminal (optional): 300 VAC
Response time		Approx. 20 ms (at the range of 10 kHz)
A/D converter		16 bits, 100 kHz max.
Temperature stability		Zero point: Within 0.03% FS/°C Gain (range): Within 0.02% FS/°C
Weight		240 g

Charge Converter (AP11-901)

Gain		1.0 mV/pC ±5%
Max. input charge		5000 pC
Frequency range		Approx. 1.6 Hz to 50 kHz
Max. output voltage		5 Vp-p or lower
Drive voltage		12 to 25 VDC
Drive current		0.5 to 5.0 mA
Rated noise		20 µVrms or lower
Phase		180°(Inverted input is output.)
Operating temperature		-20 to 80°C
Connector		Input: Miniature connector (10-32) Output: Male BNC terminal
Weight		20 g

Charge Converter (AP11-902)

Gain		1.0 mV/pC ±5%
Max. input charge		5000 pC
Frequency range		Approx. 1.6 Hz to 50 kHz
Max. output voltage		5 Vp-p or lower
Drive voltage		12 to 25 VDC
Drive current		0.5 to 5.0 mA
Rated noise		20 µVrms or lower
Phase		180°(Inverted input is output.)
Operating temperature		-20 to 80°C
Connector		Input: Miniature connector (10-32) Output: Male BNC terminal
Weight		65 g

Charge Converter (AP11-903)

Gain		1.0 mV/pC ±5%
Max. input charge		50000 pC
Frequency range		Approx. 1.6 Hz to 50 kHz
Max. output voltage		5 Vp-p or lower
Drive voltage		12 to 25 VDC
Drive current		0.5 to 5.0 mA
Rated noise		20 µVrms or lower
Phase		180°(Inverted input is output.)
Operating temperature		-20 to 80°C
Connector		Input: Miniature connector (10-32) Output: Male BNC terminal
Weight		65 g

	Name	Model	Rating
Main unit	Omniace II	RA1100	Data acquisition system without printer
		RA1200	Data acquisition system with printer, paperspeed:25 mm/s max.
		RA1300	Data acquisition system with printer, paperspeed:100 mm/s max.

Standard accessories

AC power cable x 1, Recording paper x1(RA1200/1300), Paper holder x 1 (RA1200/1300), Slot cover plateforinput and interface units x 1 set, and user's manual x1set