NEC三榮 記錄儀 RA1300

                        NEC三榮 記錄儀 RA1300:

                        RA1100特點：(已停產）
                        = 可以并行采集16通道模擬信號或64路邏輯信號，也可模擬信號，邏輯信號混合輸入。
                        =
                        10種輸入放大模塊，可直接對電壓，振動，應變，頻率，溫度，邏輯信號進行**測量。每種模塊的每一個通道*高采樣速率為100KHz或1MHz，模擬通道A/D分辨率可達16位。
                        = 既可對多通道數據同時進行時域算術運算，也可進行實時頻域分析。
                        = 10.4英寸TFT彩色高亮度顯示器，能在陽光下使用。耐磨型觸摸屏，操作方便可靠；薄膜按鍵，防塵防水。
                        =
                        采用專用操作系統，啟動時間短，運行穩定，適于廠礦、車間等外場或實驗室信號監測記錄。數據可通過調制解調器發至異地的傳真機。
                        =
                        OmniView測量控制軟件，通過以太網接口，RS-232口、GPIB口實現計算機與記錄儀之間的通訊，其數據格式與MS
                        Windows兼容。
                        
                        主機型號及規格參數
                        =
                        三種型號：RA1100無打印機，RA1200配有25mm/S熱敏打印機，RA1300配有100mm/s熱敏打印機。具有10.4英寸顯示器，內置軟驅、PC卡插槽，交直流兩用。
                        = 四種工作模式：存儲器模式、實時模式、存檔模式、瞬態模式
                        = 主機選件：擴展內存、MO驅動器、直流電源及交流橋壓源（配合交流應變模塊使用）。
                        = 接口模塊選件：RS-232C接口模塊、GP-IB接口模塊、SCSI接口塊
                        = 8個信號調理模塊插槽，可安裝多種輸入放大模塊。
                        = 多種分析軟件選件：FFT分析軟件、波形判斷軟件、算術運算選件。
                        
                        信號調理模塊規格
                        模塊型號 分辨率 采樣率 功能
                        
                        AP11-101 16位 100KHz
                        雙通道隔離電壓測試模塊，量程：±100mV～±500V，12檔。精度優于±0.3%FS（典型）
                        
                        AP11-102 16位 100KHz
                        除具有AP11-101功能外，可直接連接ICP傳感器，內置11檔程控抗混濾波器。
                        
                        AP11-103 12位 1MHz
                        雙通道隔離電壓測試模塊，量程：±100mV～±500V，12檔。精度優于±0.5%FS（典型）。頻帶：DC-400KHz，6檔低通濾波，適于測試高速信號。
                        
                        AP11-104 16位 100KHz
                        雙通道應變測試模塊，交流橋壓源。量程：1Kμε-20Kμε，5檔。頻帶：DC-2KHz
                        
                        AP11-105   1MHz 八通道邏輯電壓及觸點開關信號測試模塊， 電壓范圍：0-24V
                        
                        AP11-106 15位 100KHz
                        雙通道K、J、T、R、W型熱電偶及電壓測試模塊，電壓量程：±100mV～±500V，共9檔。熱電偶測試精度優于±0.5%FS，電壓測試精度優于±0.5%FS。
                        
                        AP11-107 14位 100KHz
                        通道K、J、T、R型熱電偶及電壓測試模塊，電壓量程：±100mV～±500V，共12檔。熱電偶測試精度優于±0.5%FS，電壓測試精度優于±0.5%FS。
                        
                        AP11-108 16位
                        100KHz單通道頻壓轉換模塊，輸入頻率范圍：1Hz-10KHz；量程：100Hz-10KHz，共7檔。精度優于±0.5%FS。充許輸入電壓為±100V
                        
                        AP11-109 16位
                        100KHz除具有AP11-101功能外，可直接連接ICP傳感器，實時計算輸入信號的RMS值
                        
                        AP11-110 16位 100KHz
                        雙通道應變測試模塊，量程800με-50Kμε，10檔。頻帶：DC-50KHz，精度優于±0.3%FS。橋壓2V或5V。應變計阻值120-2000歐，可自動平衡橋路。




Basic Specifications

Trigger Specifications

Trigger Mode	OR, AND, A*B, WINDOW
Trigger Source	Input Signal, time trigger(startingtime, ending time, measurement interval), manual trigger and external trigger
Trigger Setting	Amps other than event amps   Trigger Slope OR, AND.....or     A*B...orfor each A,B source     WINDOW...OUT or IN Level Setting: To besetwith physical values (e.g. voltage)
	Event Amp   State Settings: H, L, or OFF can be set for each input(withouttrigger slope) When OFF is set, trigger condition is notapplied.   Trigger Setting: AND or OR of the statesettingconditions of inputs from 1 to 8
Trigger Related Functions	Pre-trigger , trigger pass count,triggerfilter, and trigger mark

Other Specifications

AC Bridge Power Supply Unit (Optional)

Memory Mode

Real-Time Mode (RA1200/RA1300)

Transient Mode

Filing Mode

FFT Unit (Optional)

Arithmetic Operation Unit (Optional)

Waveform Judgment Unit (Optional)

2-CH High Resolution Amp (AP11-101)

Input		2channels/unit, isolated unbalanced input,isolatedBNC connector
Input coupling		AC and DC coupling
Input impedance		1Mor higher
Measurement range		0.1, 0.2, 0.5, 1, 2, 5, 10, 20, 50,100,200, and 500 V
Range accuracy		Within 0.3% FS (Within 0.8% FS at 500V)
Offset accuracy		Within 0.3% FS (at 25°C)
Linearity		Within 0.1% FS
Allowableinputvoltage		Range of 10 V to 500 V: 500 V max.(ACor DC peak values) Range of 0.1 V to 5 V: 100 V max. (AC or DC peak values)
CMV		Unit only: 43 V (AC or DCpeakvalues)When using isolated BNC cable (optional): 300 VAC
Frequency response		At DC coupling: DC to 50 kHz (+0.5,-3dB) At AC coupling: 0.3 to 50 kHz (+0.5, -3 dB)
Low-pass filter		Bessel type (attenuation factor:-12dB/OCT) 30, 300, 3 kHz, and OFF (+0.5, -3 dB)
A/D converter		16 bits, 100 kHz max. (twochannelsimultaneous sampling)
Temperature stability		Zero point: Within 0.03% FS/°C Gain (range): Within 0.01% FS/°C
Weight		230 g

2-CH High Speed Amp (AP11-103)

Input		2channels/unit, isolated unbalanced input,isolatedBNC connector
Input coupling		AC and DC coupling
Input impedance		1Mor higher
Measurement range		0.1, 0.2, 0.5, 1, 2, 5, 10, 20, 50,100,200, and 500 V
Range accuracy		Within 0.5% FS (Within 0.8% FS at 500V)
Offset accuracy		Within 0.5% FS (at 25°C)
Linearity		Within 0.2% FS
Allowableinputvoltage		Range of 10 V to 500 V: 500 V max.(ACor DC peak values) Range of 0.1 V to 5 V: 100 V max. (AC or DC peak values)
CMV		Unit only: 43 V (AC or DCpeakvalues)When using isolated BNC cable (optional): 300 VAC
Frequency response		At DC coupling: DC to 400 kHz (+0.5,-3dB) At AC coupling: 0.3 to 400 kHz (+0.5, -3 dB)
Low-pass filter		Bessel type (attenuation factor:-12dB/OCT) 50, 500, 5 kHz, and OFF (+0.5, -3 dB)
A/D converter		12 bits, 1 MHz max. (twochannelsimultaneous sampling)
Temperature stability		Zero point: Within 0.03% FS/°C Gain (range): Within 0.01% FS/°C
Weight		240 g

2-CH TC/DC Amp (AP11-106)

Input		2channels/unit, isolated unbalanced input,terminalblock 4
Input coupling		DC coupling
Input impedance		10Mor higher
Thermocouple		R, T, J, K, and W
Measurement range		R: 0 to 1600°C T: -200 to 400°C J: -200 to 1000°C K: -200 to 1350°C W: 0 to 2300°C
Voltagemeasurementrange		100, 200, 500 mV, 1, 2, 5, 10, 20 and50V FS
Range accuracy		Temperature: Within 0.5% FS (Within1%FS at 0°C or lower) Voltage: Within 0.5% FS
Coldjunctioncompensation		Internal/external switchable Accuracy: Within 2°C (Within 1°C at stable temperature of 20°Catinput terminal)
Linearity		Within 0.1% FS
Allowableinputvoltage		50 V (AC or DC peak values)
CMV		43 V (AC or DC peak values)
Frequency response		DC to 40 kHz (+0.5, -3 dB)
Low-pass filter		Bessel type (attenuation factor:-18dB/OCT) 1, 30, 500, 5 kHz, and OFF (+0.5, -3 dB)
A/D converter		15 bits, 100 kHz max. (twochannelsimultaneous sampling)
Temperature stability		Accuracy: 0.04% FS/°C (When usedastemperature amp) Zero point: Within 0.03% FS/°C (When used as DC amp) Gain (range): Within 0.01% FS/°C
Weight		240 g

TC/DC Amp (AP11-107)

Input		1 channel/unit, isolated unbalanced input, 2bindingposts
Input coupling		DC coupling
Input impedance		10M or higher (1M at 5, 10, 20, 50 V FS in DC amp)
Thermocouple		R, T, J, K
Measurement range		R: 0 to 800°C at 800°C FS and 0to1600°C at 1600°C FS T: -200 to 200°C at 200°C FS and -200 to 400°C at 400°CFS J: -200 to 200°C at 200°C FS and -200 to 1000°C at 1000°C K: -200 to 200°C at 200°C FS and -200 to 1200°C at 1200°C
Voltagemeasurementrange		10, 20, 50, 100, 200, 500 mV, 1, 2,5,10, 20, and 50 V FS
Range accuracy		Temperature: Within 0.5% FS (Within1%FS at 0°C or lower) Voltage: Within 0.5% FS
Linearity		Within 0.1% FS
Allowableinputvoltage		50 V (AC or DC peak values)
CMV		300V (AC or DC peak values)
Frequency response		DC to 40 kHz (+0.5, -3 dB)
Low-pass filter		Bessel type (attenuation factor:-18dB/OCT) 1, 30, 500, 5 kHz, and OFF (+0.5, -3 dB)
Referencejunctioncompensation		Internal/external switchable
A/D converter		14 bits, 100 kHz max.
Weight		200 g

Event Amp (AP11-105)

Number of channels		8 channels/unit
Input signal		Sets voltage or contact foreachchannel Voltage input: Input voltage range 0 to +24 V Detection level H level...2.5 V or higher   L level...0.5 V or lower Contact input: Close...250 or lower   Open...2 kor higher
Response time		1µs or faster (Input level should be+5V or higher.)
Input connector		Round DIN connector 8P...2 pcs. Event amp side: XT2B-0800(Conformed to DIN45326)
Weight		100 g

2-CH AC Strain Amp (AP11-104)

Number of channels		2 channels/unit, isolated balanced input,NDISconnector
Applicablegaugeresistance		120to 1k
Bridge power supply		Sine wave 2 Vrms, 5 kHz (Bridgepowersupply is supplied separately.)
Gauge factor		1.9 to 2.2
Range of balance		Resistance: 2% (10000 µ)or lower Capacitance: 2000 pF or lower
Balance method		Resistance: Auto-balance Capacitance: Auto-balance (500 pF or lower,eliminatingconstantly) Balance time: Within 1s at 1 ch Within 0.5%Fs Remainedvoltageaccuracy
Maximum sensitivity		Over full-scale at 500 µ(at 2 V or higher bridge voltage)
Measurement range		1, 2, 5, 10, 20 kµFS
Internalcalibratorand accuracy		0.5 k, 1 k, 2 k, 3 k, 5 kµAccuracy: Within 0.5% FS
Linearity		0.2% FS
CMV		300 VAC
Frequency response		DC to 2 kHz (+0.5, -3dB)
Low-pass filter		Butterworth type (attenuationfactor:-12 dB/OCT) 10, 30 , 100, 300 Hz, and OFF (+0.5, -3 dB)
A/D converter		16 bits, 100 kHz max.
Temperature stability		Zero point: Within 0.05% FS/°C Gain (range): Within 0.05% FS/°C
Weight		285 g

2-CH DC Strain Amp (AP11-110)

Number of channels		2 channels/unit, isolatedbalancedinput, NDIS connector
Input coupling		DC
Input impedance		10M+10Mor higher
Bridge power supply		2 V and 5 V
Applicablegaugeresistance		120 to 2 k (at BV = 2V),350 to 2k (at BV=5 V)
Gauge factor		2
Range of balance		2% (15000 µorlower
Balance method		Resistance: Auto-balance Balance time: 0.5 sec max. at 1ch Remained voltage accuracy: Within 0.3% FS
Measurement range		2, 5, 10, 20, 50 kµFS (at BV = 2 V) 0.8, 2, 4, 8, 20 kµFS(BV= 5 V)
Voltagemeasurementrange		2, 5, 10, 20, 50 mV FS
Range accuracy		Within 0.3% FS
Linearity		0.1% FS
Allowableinputvoltage		8 V (DC or AC peak values)
Frequency response		DC to 50 kHz (+0.5, -3dB)
Low-pass filter		Bessel type (attenuation factor:-12dB/OCT) 10, 30, 300 Hz, 1 kHz, and OFF (+0.5, -3 dB)
Temperature stability		Zero point: Within 0.1% FS/°C Gain (range): Within 0.01% FS/°C
CMV		300 VAC
A/D converter		16 bits, 100 kHz max
Weight		240 g

2-CH Vibration/RMS Amp (AP11-109)

Input		2 channels/unit, isolatedunbalancedinput, isolated BNC connector
Input coupling		AC and DC
Input impedance		10 Morhigher
Power supplyforsensor		2 mA, 18 V or higher
Measurement range		0.1, 0.2, 0.5, 1, 2, 5, 10, 20, 50,100,200, 500 V
Range accuracy		DC amp range: Within 0.3% FS(Within0.8% FS at 500 V) RMS amp range: Within 2% FS (at DC and 40 Hz to 20 kHz)
Linearity		Within 0.1% FS
Crest factor		2.8 max. (RMS amp)
CMV		Unit only: 42 V (DC or ACpeakvalues) When isolated BNC cable (optional) is used: 300 V AC
Frequency response		DC coupling: DC to 50 kHz (+1,-3dB) AC coupling: 1 to 50 kHz (+1, -3 dB)
Low-pass filter		Butterworth type (attenuationfactor:-24 dB/OCT) 30, 100, 300 Hz, 1 kHz, and OFF
High-pass filter		Butterworth type (attenuationfactor:-24 dB/OCT) 10, 30, 100 Hz, and OFF
A/D converter		16 bits, 100 kHz max.
Temperature stability		Zero point: Within 0.02% FS/°C Gain (range): Within 0.01% FS/°C
Weight		270 g

2-CH FFT Amp (AP11-102)

Input		2 channels/unit, isolatedunbalancedinput, isolated BNC connector
Input coupling		AC and DC (only AC couplingwhenamp-embedded charge accelerometer is used)
Input impedance		1 Mor higher
Power supplyforsensor		2 mA, 18 V or higher
Measurement range		0.1, 0.2, 0.5, 1, 2, 5, 10, 20, 50,100,200, 500 V
Range accuracy		Within 0.3% FS (Within 0.8% FS at 500V)
Linearity		Within 0.1% FS
Maximum input voltage		500 V (DC or AC peak values) (30 V atACcoupling of 0.1 to 5 V)
CMV		Unit only: 42 V (DC or ACpeakvalues) When isolated BNC cable (optional) is used: 300 V AC
Frequency response		DC coupling: DC to 50 kHz (+0.5,-3dB) AC coupling: 0.3 to 50 kHz (+0.5, -3 dB)
Low-pass filter		Bessel type (attenuation factor:-24dB/OCT) 30, 300 Hz, 3 kHz, and OFF (+0.5, -3 dB)
Anti-aliasing filter		20, 40, 80, 200, 400, 800 Hz, 2, 4,8,20, and 40 kHz Drop characteristic: -72 dB typ. at 1.5 x fc
Offset accuracy		Within 0.3% FS (at 25 °C)
A/D converter		16 bits, 100 kHz max.
Temperature stability		Zero point: Within 0.02% FS/°C Gain (range): Within 0.01% FS/°C
Weight		240 g

F/V Converter (AP11-108)

Input		1 channel/unit, isolatedunbalancedinput, isolated BNC connector
Input coupling		AC and DC
Input impedance		100 M or higher
Input frequency range		1 Hz to 10 kHz (Pulse width: 20 µsorlonger)
Measurement range		0.1, 0.2, 0.5, 1, 2, 5, 10 kHz FS
Range accuracy		Within 0.5% FS (Within 0.8% FS at 500V)
Linearity		Within 0.3% FS
Trigger level		Selectable from 0 V and 2.5 V
Allowableinputvoltage		100 V (AC or DC peak values)
CMV		Unit only: 42 V (AC or DCpeakvalues) Between isolated BNC and safety terminal (optional): 300 VAC
Response time		Approx. 20 ms (at the range of 10 kHz)
A/D converter		16 bits, 100 kHz max.
Temperature stability		Zero point: Within 0.03% FS/°C Gain (range): Within 0.02% FS/°C
Weight		240 g

Charge Converter (AP11-901)

Charge Converter (AP11-902)

Charge Converter (AP11-903)

產品留言

標題

聯系人

聯繫電話

內容

驗證碼

點擊換一張

注：1.可以使用快速鍵Alt+S或Ctrl+Enter發送資訊!
2.如有必要,請您留下您的詳細聯繫方式!